Under what condition are the planet wheels of a differential unit rotating

When the vehicle is turning corner

When the vehicle is traveling on the overrun

When the vehicle is traveling straight ahead

What are the main items in the image shown

Constant velocity joint, plunge joint and rubber boots

Hookes type joints layshaft coupling and rubber boots

Constant velocity joints, bylaws and propeller shaft

Hookes type joints, propeller shaft and latex gaters

Which one of the following is correct with regards to combined clutch release bearing and hydraulic operating cylinder

It is normally adjusted by a separate cable

It is normally adjusted on the clutch pedal

It is normally adjusted by adding fluid

To disengage the clutch excessive force is required. What components should be checked first

Clutch pressure plate, driven plate, flywheel face and master/slave cylinder

Pedal drive shaft, transmission mounts and the master/slave cylinder

Pedal mechanism, clutch cable, release shaft, master/slave cylinder and hose

Clutch driven plate, input shaft splines, clutch cable, and master/slave cylinder

What is one function of clutch

Control the torque transmitted from the engine to transmission system

Prevent two gears being selected at the same time

Allow the driver to overrun the vehicle when travelling downhill

Provide a means of increasing engine power as engine speed increases

How can a repaired transmission unit be checked for correct operation

By ensuring all up and down gear changes are smooth

By ensuring that gears can only be selected easily at road speeds over 25 Km/hr

By changing directly from fifth gear at road speeds over 65 Km/hr

By changing through all gears without the use of clutch

Which one of the following is correct with regards to the clutch cover?

It is splined onto the input shaft

It is splined to the clutch disc

It is bolted to the input shaft

Under what condition are the planet wheels off a differential unit rotating

When the vehicle is turning a corner

When the vehicle is traveling on the over-run

When the vehicle is travelling straight ahead

What does a differential allow when a vehicle is travelling round a corner

Outer wheel to travel faster than the inner wheel

Inner wheel to travel faster than the outer wheel

Inner and outer wheels to travel at the same rate

Wheels to automatically brake if speed is exceeded

What is the main reason for using a constant velocity joint in the drive system

It is capable of driving through a large angle

It multiplies torque at the road wheels

It reduces the need for regular servicing

It can increase road speed at the wheel

Why is it necessary to use a clutch alignment tool

Align the drive plate centrally

To align the flywheel to the bell housing

What does a clutch allow

Gradual take up of drive from the engine

The engine to provide a braking force down hill

Means of giving an overdrive ratio in 5 th gear

Decrease in engine power as engine speed decreases

What is a routine inspection of the component shown in the image

Check rubber gaiters and feel for free play

Strip down joints, re-grease and tighten balls

Remove, refit and check runout using V blocks

What does the mean radius of the clutch driven plate affect

Amount of torque it can transmit

Pressure applied to the flywheel

What is the best method of testing a newly fitted manual gearbox

Carry out a road test and check gears function correctly

Carry out a bench test checking all gears are selectable

Give the car to the customer to test for a couple of days

Raise the vehicle on a hoist and select all forward gears

Which one of following is a routine check on a rear axle final drive unit?

Remove the level plug and top up with extreme pressure grade oil

Remove the propeller shaft to tighten the pinion nut

Remove the level plug and top up with extreme pressure grease

Remove the level plug and top up with multi-grade engine oil

Before removing the gearbox to change the clutch, why may it be necessary to use special equipment

To compress the dual mass flywheel unit

The CV gaiter shown has split due to fair wear and tear. The joint is examined and found to be serviceable. What is the correct working procedure

Clean, repack with grease and fit a new gaiter

Pack with grease and glue the split together

Fit a new gaiter and fil with correct grade of oil

Clean with brake cleaner and fit a new gaiter

What is one function of a clutch

Allow the engine to keep running when the vehicle is temporarily stopped

Provide a means of increasing engine power as engine speed increases

Provide a means of giving a direct drive in top and reverse gear

Allow the driver to control driving torque at all speeds

What test should be carried out after replacing a clutch cable

Clutch drag when the brakes are fully applied

Clutch slip when braking at high road speed

Clutch drag at maximum road speed

Which one of the following pieces of equipment would assist in the removal of the gearbox from a front wheel drive light vehicle

Clutch cable holding and mounting pins

Rear axle locating and alignment pins

Propeller shaft splitting equipment

What is the purpose of the labelled items in the image shown

Prevents more than one gear being selected at a time

Reduces the effort required to change gear

Allows a positive engagement of the gear selected

Reduces vibration of the shift forks and shafts

Transmission level 2

Authored by Craig Billington

Professional Development

University

Used 196+ times

AI Actions

Add similar questions

Adjust reading levels

Convert to real-world scenario

Translate activity

More...

Content View

Student View

71 questions

Show all answers

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

Which one of the following is a function of the clutch assembly

Provides a temporary break in the transmission of drive.

Reduces gearbox torque

Provides a permanent break in the transmission of drive.

Increase gearbox torque

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

Which component provides the clamping pressure for the clutch shown in the image

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

What is the part of the gearbox which bolts to the engine block

Tail extension

Bell housing

Drive plate

Input shaft

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

What is illustrated in the image shown

Reverse gear idler

Gearbox interlock device

Synchromesh selection unit

Differential drive unit

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

What is the main type of gear used in constant mesh

Bevel

Helical

Hypoid

Spur

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

Referring to the diagram, if X is the driver gear and rotate anti-clockwise at 2000 rev/min, at what speed and direction will gear Y rotate

Clockwise at 4000 rev/min

Clockwise at 1000 rev/min

Anti-clockwise at 1000 rev/min

Anti-clockwise at 2000 rev/min

MULTIPLE CHOICE QUESTION

30 sec • 1 pt

What fault could a worn spring cause in the image below

Two gears to be selected

Gears to automatically disengage

Gears to automatically engage

A whining noise

Access all questions and much more by creating a free account

Create resources

Host any resource

Get auto-graded reports

Continue with Google

Continue with Email

Continue with Microsoft

or continue with

Facebook

Apple

Others

Already have an account?

Similar Resources on Wayground

66 questions

MSSC Quality Review 1

Quiz

•

11th Grade - Professi...

66 questions

MCQ #2 - Finance 1

Quiz

•

University

72 questions

Introduction to Automobile Engineering

Quiz

•

University

69 questions

312課程模式325區分性課程與教學326教育模式

Quiz

•

University

Popular Resources on Wayground

24 questions

PBIS-HGMS Day 10

Quiz

•

6th - 8th Grade

10 questions

HCS SCI 03 Summer School Review 3

Quiz

•

3rd Grade

11 questions

Home Scope

Quiz

•

7th - 8th Grade

15 questions

HCS SCI 05 Summer School Assessment 3 Review

Quiz

•

5th Grade

35 questions

Lufkin Road Middle School Student Handbook & Policies Assessment

Quiz

•

7th Grade

18 questions

Geo 11.3 Area of Circles and Sectors

Quiz

•

9th - 11th Grade

Transmission level 2

Which one of the following is a function of the clutch assembly

Which component provides the clamping pressure for the clutch shown in the image

What is the part of the gearbox which bolts to the engine block

What is illustrated in the image shown

What is the main type of gear used in constant mesh

Referring to the diagram, if X is the driver gear and rotate anti-clockwise at 2000 rev/min, at what speed and direction will gear Y rotate

What fault could a worn spring cause in the image below

Which one of the following is most likely be fitted to a propeller shaft

Under what condition are the planet wheels of a differential unit rotating

What are the main items in the image shown

Access all questions and much more by creating a free account

Similar Resources on Wayground

Popular Resources on Wayground