Untitled Presentation
Presentation
•
Construction
•
Vocational training
•
Practice Problem
•
Hard
Steve Robbins
FREE Resource
43 Slides • 28 Questions
1
2
3
Multiple Choice
Which of the following is NOT a reason for using WRAS approved products in domestic cold water systems?
Water Regulations
Back flow
Contamination
Cost reduction
4
Open Ended
Why is it important for plumbers in the UK to use approved materials, fittings, and appliances when working with domestic cold water systems?
5
6
Multiple Choice
Which type of valve is commonly used on incoming mains for high pressure applications?
Screw down stop valve
Fullway gate valve
Spherical plug valve
Slotted service valve
7
8
Open Ended
Explain the difference between a screw down stop valve and a fullway gate valve in terms of pressure suitability and internal mechanism.
9
10
Fill in the Blanks
Type answer...
11
12
Multiple Choice
What is the correct BSP tail size for pillar taps used on baths?
1/2 inch
3/4 inch
1 inch
5/8 inch
13
14
Multiple Select
Which of the following valves can be used for both high and low pressure systems?
Screw down stop valve
Spherical plug valve
Fullway gate valve
Slotted service valve
15
16
Open Ended
Looking at the diagram, describe where you would place a screw down stop valve and a gate valve in a typical domestic water system.
17
18
Multiple Choice
Which type of tap is commonly used on kitchen sinks and has a longer neck to allow a larger air gap?
High neck pillar tap
Mixer tap
Bi-flow mixer tap
Bib tap
19
20
Multiple Choice
Which type of tap can only be fitted on equal pressure systems?
Mixer tap
High neck pillar tap
Bib tap
Bi-flow mixer tap
21
22
Fill in the Blanks
Type answer...
23
24
Multiple Choice
Which of the following statements about bib taps is correct?
They are fitted above a cleaner’s sink or as a hose union tap.
They mix hot and cold water inside the body of the tap.
They have a single spout divided down the middle.
They are used on kitchen sinks.
25
26
Open Ended
Explain the difference between a true mixer tap and a bi-flow mixer tap in terms of how water is mixed and exits the tap.
27
28
Open Ended
List the three basic types of taps mentioned in the lesson.
29
30
Multiple Choice
Which component in a rising spindle tap is responsible for maintaining the watertight seal around the spindle?
Packing gland
Tap wheel head
Jumper and washer
Head workings
31
32
Multiple Select
Which of the following tools are used to dismantle a non-rising spindle tap?
Circlip spanner
Adjustable spanner
Grips
Screwdriver
33
34
Fill in the Blanks
Type answer...
35
Open Ended
Compare the mechanisms of watertight sealing in rising spindle taps, non-rising spindle taps, and quarter turn taps.
36
37
Multiple Choice
According to Water Regulations, what is the primary reason for including protection measures in a cold water storage cistern?
To prevent contamination
To increase water pressure
To reduce maintenance costs
To improve water taste
38
39
Multiple Select
Which of the following are recommended features for a cold water storage cistern to ensure safety and maintenance?
Effective inlet control
Screened warning/overflow pipe
Insulation against freezing
Open top for ventilation
40
41
42
Open Ended
Explain why it is important to install the cold feed 25mm higher than the cold distribution in a cold water storage cistern.
43
Multiple Choice
What is the main difference between the cold feed and cold distribution in a cold water storage cistern?
Cold feed supplies water to outlets, cold distribution supplies water to the hot water cylinder.
Cold feed is installed lower than cold distribution, cold distribution is installed higher.
Cold feed supplies water to the hot water cylinder, cold distribution supplies water to various outlets.
Cold feed and cold distribution have the same installation height.
44
45
Multiple Choice
Which of the following materials is NOT commonly used for cold water storage cisterns?
Plastic
Fibre glass
Copper
Galvanised steel
46
47
48
Multiple Select
Which items are essential components of a cold water storage cistern as shown in the diagram?
Warning pipe
Screened vent
Overflow pipe
Grommet for open vent
49
50
Fill in the Blanks
Type answer...
51
52
Open Ended
Describe the function of the rubber washer and neoprene washer in the compression tank connector assembly for a cold water storage cistern.
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
Open Ended
Reflecting on what you have learned about approved products in domestic cold water systems, what questions do you still have or what would you like to know more about regarding water regulations or product approval?
71
Multiple Choice
Why is it a legal requirement for plumbers in the UK to use approved materials, fittings, and appliances in domestic cold water systems?
To comply with water regulations and prevent issues such as back flow, contamination, and corrosion
To reduce installation costs
To speed up the plumbing process
To avoid using imported products
Show answer
Auto Play
Slide 1 / 71
SLIDE
Similar Resources on Wayground
67 questions
Brady's end of summer quiz!!!
Presentation
•
Professional Development
67 questions
Cardiophysio
Presentation
•
KG - University
67 questions
ACCESS PD December 4th, 2025
Presentation
•
University - Professi...
67 questions
Plant Form
Presentation
•
University
59 questions
Superlatives
Presentation
•
Professional Development
65 questions
AVTC4 - LESSON 15
Presentation
•
University
67 questions
ESB V2 Unit 1
Presentation
•
Professional Development
65 questions
PHNAVY BMC Lecture 2 - Radiation
Presentation
•
Professional Development
Popular Resources on Wayground
10 questions
HCS SCI 03 Summer School Review 4
Quiz
•
3rd Grade
11 questions
HSMS - Standard Response Protocol
Quiz
•
6th - 8th Grade
16 questions
1.1-1.2 Quiz Review
Quiz
•
9th - 12th Grade
12 questions
Exponent Expressions
Quiz
•
6th Grade
20 questions
Adding and Subtracting Integers
Quiz
•
6th - 7th Grade
11 questions
Northeast States
Quiz
•
3rd - 4th Grade
10 questions
Characterization
Quiz
•
3rd - 7th Grade
10 questions
Common Denominators
Quiz
•
5th Grade